![](/uploads/1/2/7/6/127608093/764146932.jpg)
BMW INPA / Ediabas K+DCAN USB Interface, DCAN USB Interface, K+DCAN, K+DCAN USB Interface. For Driver downloads please go directly to the FTDI Driver Page. Jul 07, 2016 The only thing needed to do is to configure your BMW K-CAN D-CAN USB Cable. During the installation, the drivers for the cable were installed. Now plug it in your USB port and Windows should recognize it and begin installing it.If Windows did not recognize the cable or could not find the correct drivers, see the Troubleshooting section below.
BMW INPA Ediabas Windows 10 64-bit Installation GuideHere is the educational tutorial on installing BMW INPA/EDIABAS diagnostic software on Windows 10 64-bit. Enjoy.Disclaimer:You are at your risk.
INPA will work with few select things for an E38 such as resetting adaptations, diagnostics, code reading, etc. NCS Expert will NOT run on a 64-bit operating system. If you have a 32-bit version of Windows 10, please feel free to try ECS Expert and let me know if it works!Credits: perishalive92Pre-installation Download:USB interfaceYou will Winrar or 7zip or a.rar file extractor similar to those.Inpa softwareINPA Cable softwareShould you get ANY errors or pop-ups during any phase of the installation, ignore them. INPA will still install.Pre-Installation1.Download all required files and programs,as listed below.
Night to remember shalamar download. 2015-09-18T21:01:08Z Comment byCan i get a copy of this [email protected] 2015-03-22T19:54:05Z Comment by@damagician78: [email protected] 2014-10-23T19:25:53Z Comment byi would really like a download link for this song.
Also you should have the K+DCAN cable in your possession(link provided below).2.Extract the INPA.rar to your desktop. You will be left with INPA folder.3.Extract INPAcable.rar to your desktop. You will be left with INPA cable folder.InstallationPhase 11.Open INPA cable folder and move the top four folders (step1, step2, step3 and driver) to Windows(C folder of your PC.2.Whilst in Windows(C, open 01Step1 folder and copy EC-APPS over to your Windows(C drive.3.Go back to 01Step1 folder and open the NFS folder. Open Entpackt folder.
![Bmw Inpa Ediabas Kdcan Usb Driver Bmw Inpa Ediabas Kdcan Usb Driver](/uploads/1/2/7/6/127608093/635000050.jpg)
Open disk 1, find SETUP.exe and right-click it. Goto Properties/Compatibility and set it to run in compatibilty mode for Windows XP (Service Pack 3). Also, check the box for Run as Administrator.
Hit Apply then Ok.4.Double-click SETUP.exe to launch.5. Once window pops up, select Windows XP. Click Weiter (it means Next).6.Click Weiter 3 more times.
![Ft232r usb uart driver Ft232r usb uart driver](http://www.one-stop-electronics.com/shop/images/detailed/interface_ready_new.jpg)
Make sure User Mode is selected. Click weiter.7.Make sure top choice is selected (1 Parametri). Click Weiter.8.Ensure OBD is selected. Press weiter. Ensure Kein API-TRACE. Click weiter.
Ensure Kein IFH-TRACE is selected. Click weiter.Ensure Komfort(.IPO) is selected. Press weiter.9.Press OK. Press ok, and again. Press any key to continue.10.Select Ja,Computer jetzt neu starten.
Click Breeden. This will restart your PC as needed.Phase 21.Goto Windows( C/02Step2/INSTALL and right click on Instprog. Set it up to run in compatibility mode as mentioned in Phase1, step 3. Then double-click to launch.2.Press OK if prompted. Select Enlgish then press weiter.3.Press continue and continue again. Ensure destination is under C:4. Press continue.
Select BMW Group Rectification programs UK. (NOT USA) Press continue.5.Check off all white boxs. There will be 2 update and 1 complete that needs to be checked. Press continue, and again. You may get error.
Otherwise, press End.6.Restart your PC once more manually.Phase 31.Goto Windows (C/03Step3/INSTALL and right click on Instprog. Set it up to run in compatibility mode as mentioned in Phase1, step 3. Then double-click to launch.2.Press OK if prompted.
Select English then press weiter.3.Press continue and continue again. Ensure destination is under C:4.
Press continue. Select BMW Group Rectification programs UK. (NOT USA) Press continue.5.Under INPA 5.0.1, check off Update. Under NCS Expert 3.0.8, check off Complete. Press continue.6.Click on Rename. In the box, type the number 1 and press continue, and again. You might gett error.
IF prompted, press End.Phase 41.Plug in your cable. You will from now on use ONLY that port.Windows 10 will automatically update the driver IF needed. Windows 10 also already has a serial function.
This is all we need to modify.2.In your search box (lower left of screen next to Windows button), type “Device Manager”. Click on the top option.3.Once in Device Manager, locate Ports(COM & LPT) and click on the little plus sign next to it. It should now show USB Serial Port (COMx) under Ports(COM & LPT).The little ‘x’ is in place of whatever number you have the cable plugged into).4.Right-click on USB Serial Port (COMx) and click Properties.5.Goto Port Settings tab.
Click Advanced. Change the COM Port Number to COM1.6.Change Latency Timer from 16 to 1. Press ok again.
Close Device Manager.7.Goto Windows(C/DriverDCANUSB and double-click OBDSetup.exe. Press Enter.Phase 51.Go into Control Panel/System/Advanced System Settings/Environment Variables.2.Ensure that System Variables TMP and TEMP both contain the path C:EDIABASBin.3.If not, manually add it in. Example: C:WindowsTemp;C:EDIABASBin4.the ‘;’ is important to seperate paths. Please ensure you put that in there then add in the rest.Phase 61.From Desktop, open INPA folder then open the second INPA folder. Right click on Step1InstallBMWTools and click Poperties.
Goto Compatibilty and run the program in compatibility mode for Windows 7. Also, run as administrator. Click Apply then ok.
Doulbe-click to launch.2.Enusre destination path is C:BMW Tools, if it is not change it to that.3.Press Install. You will get an error. Press ok.4.Goto Windows(C/BMW Tools/Programminstallation and right-click on setup.exe. Set it up for compatibility mode as stated in Phase 1, step 3.5.double-click to launch. Select English, press ok.
Accept and press next. Press next again and again.Ensure the installation destination is C:EDIABAS, click next.Ensure installation destination is C:EC-APPSNFS,click next.Ensure installation destination is C:EC-APPSINPA, click next.Ensure installation destination is C:NCSEXPER, click next.Ensure start menu folder is BMW Standard Tools. Click next.6.You do NOT have to perform the data backup if not desired. Uncheck box if not wanting data backup and click next.Ensure hardware-interface setting is STD:OBD and click next.Ensure COM port for serial OBD is Com1. Check the box for USB to serial adapter.
Click Install.
Many FTDI FT232RL based cables can be modified to work with INPA software for BMW diagnosis. And they are cheap as hell. Here list all possible INPA hardware cables.First of all, INPA software can be downloaded free here:INPA driver: software: of INPA cables: BMW INPA K+DCAN cable with FT232RL chip Ediabas ADS/OBD interface Non-ADS Ediabas OBDII RS232 interface INPA + 140+2.01+2.10 4 in 1 BMW Scanner Carsoft 6.5 interface BMW ICOM A2+B+C emulatorUsing experience:This is a typical FTDI based interface. This is the current most used cable for INPA.With the USB K+D CAN type cables there are a few installation steps, drivers & a little software that you need to make them work properly. This does 2001-on cars right up to & including 2011 cars (may be limited by the hookie software for cars after June 2008 on a diminishing basis as the car gets newer).
This cable is a USB enabled device, again you will need to install the USB to serial drivers. However you will also need to install the K+D CAN utility, this allows you the ability to switch it from a K CAN device for pre-2007 cars (see list above) to a DCAN cable. There are two versions of this utility, a fancy GUI & a MS DOS one. I find that the MS DOS one works best.Hera’s an image of what this cable looks like:Serial Port cableAs mentioned previously the ADS interface is a different protocol, if you don’t have an ADS interface with an e36 then what you’ll be able to read with a regular OBD cable is limited.
Unfortunately the ADS interface seems to be the hardest to get & most expensive of all the interfaces. It works fine on the e36, e39 & e63 (note my e63 is pre-March 2007) from my personal experience.Suitable for e36, e34, e30Here’s a picture of the Ediabas ADS interface:This is a cheap interface & is readily available plus requires no modification. It works just fine on E46/E39 with either the round 20 pin connector under the bonnet or the OBD2 port in the drover’s footwell. Set up of this cable is straight forward, no drivers required.This is a interface contains four software of BMW scanner INPA K DCAN cable + BMW DASH E6x V2.1.0 + BMW Scanner V1.4.0 + BMW Scanner V2.10 cable. The scanner comes with INPA OBD, ADS interface and none ADS cable for all all systems (K-line and CAN-BUS) of BMW series and OBDII diagnostic system.CarSoftware interface can be modified to work with INPA, but it is not recommended. When you first got INPA, you have to run a carsoft test to “initiate” the lead every time. What a PITA, stay away from this solution!
The black serial cable below only works on OBD1 cars like pre 2001 e39 and this will work for all K CAN (e36, e39, e46, e53, e63).BMW ICOM Rheingold not only comes with basic ISTA-D ISTA-P diagnostic & programming software, it comes with lots of engineering software, INPA, EDIABAS, WinKFP, NCS-expert, NCS-dummy etc. So INPA is well loaded to BMW ICOM A2+B+C diagnostic system, but you need to do some configuration work. Gledalica filmovi online sa prevodom.
This is quite good for experts and technician.SaveSave.
![](/uploads/1/2/7/6/127608093/764146932.jpg)